|
Additional Uses:
Non-painted: floors, walkways, storage areas, patios, decks, railing, roofs,
asphalt shingles, siding, fiberglass, boats, piers, docks, stairs, ramps, ground
statues/monuments, outdoor furniture, tennis courts (non-grass), shorelines,
gravel under benches, and other non-painted surface.
General Treatment
Notes
- Control is most easily achieved when algae is not yet well established.
- Apply early in the day under calm, sunny conditions, and when water
temperatures are warm. Sunlight and higher temperatures both enhance
GreenClean Granular Algaecide activity.
- Apply in a manner that will ensure even distribution within the
treatment area.
- Break up any heavy, floating algae mats before and during application.
- Skim dead algae and organic matter that rise to the water's surface
after treatment. Allowing dead organic matter to sink and decay will provide
a food source and additional nutrients that stimulate algae re-growth and
further blooms.
- If using GreenClean in conjunction with other water additives (such as
bacteria or enzymes), always apply GreenClean first and wait several hours
before adding any other products.
- Re-treat areas if re-growth begins to appear. Allow 48 hours between
consecutive treatments.
- Maintain an algae-free pond with maintenance rates at a frequency
appropriate for your environmental conditions.
- In regions where water freezes in the winter, treatment 6-8 weeks before
expected freeze would help prevent masses of decaying algae under the ice
cover.
- After application, do not allow undiluted granules to remain in an area
where humans or animals are exposed.
- Non-target plants will suffer contact burn if undiluted granules are
accidentally spilled on them. Do not apply in such a way that the
concentrated product comes in contact with grass, ornamentals and other
foliage.
- Do not tank mix with aquatic herbicides or algaecides containing copper
or bromides.
Directions for Use
Apply to any water or surface sites except treated, finished drinking water
reservoir or drinking water receptacles. For non-food uses only.
Water Treatment
Use to treat, control, and prevent a broad spectrum of algae. Effects of
treatment are immediately apparent (bubbling, bleaching/discoloration of algae).
Waters treated with GreenClean Granular are permissible to be used without
interruption.
| Application |
Heavy Algae Growth |
Low Algae Growth/Maintenance |
| Large Volume - Granular:
lakes, ponds, lagoons, etc. |
90-500 lbs per million
gallons of water.
30-170 lbs per acre-foot of water. |
9-50 lbs per million
gallons of water.
3-17 lbs per acre-foot of water. |
| Small Volume - Granular:
indoor or outdoor water gardens, fountains, ornamental waterfalls. |
3-16 Tbs per 1000 gallons
of water. (16 Tbs = 1 Cup, 2 Cups = 1 lb) |
1-5 tsp per 1000 gallons
of water. (3 tsp = 1 Tbs) |
Ground/Surface Treatment:Use GreenClean on
all non-painted surfaces to prevent and control algae, moss, slime molds and
their spores, and the odors and conditions these organisms cause.
| Application |
Heavy Algae Growth |
Low Algae Growth/Maintenance |
| Granular Application |
2-3 lbs per 1000 sq ft of
area. Make granular applications over wet surface or activate with water
immediately following application. (1 lb = 2 Cups) |
1-2 lbs per 1000 sq ft of
area. Make granular applications over wet surface or activate with water
immediately following application. (1 lb = 2 Cups) |
| Liquid Application |
Solution Preparation: Due to solubility
limitations, use at least 1 gallon of water to fully dissolve each 0.5
lb of GreenClean. Use same rate as the granular application above.
Dissolution in cold water takes approximately 5 minutes. |
|
Application Methods
Spreading/Broadcasting:
Broadcast with a mechanical spreader or by hand directly on the surface. A lawn
spreader or any other applicator that will ensure uniform coverage is
acceptable.
Spot Treatment:
Apply directly over the infested area. Re-treatment is required when heavy
growth occurs.
Liquid:
Make a solution with GreenClean (refer to liquid application rates). Spray this
solution on the desired treatment surface until saturated/fully covered.
Active Ingredients:
Sodium Carbonate Peroxyhydrate* 50%
Other Ingredients: 50%
Total: 100%
*Contains 27.6% Hydrogen Dioxide by weight.
|
